Why Learning Plumbing Basics is Crucial for Installing a Bathtub
BookThis great article which follows on the subject of How to Install a Bathtub is especially entertaining. Try it and make your own personal final thoughts.
Mounting a bath tub isn't exactly rocket science, but it does need solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is readily obtainable, the job can move rapidly; if you need to open up a wall to eliminate the old bathtub as well as place the new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub and set in the brand-new one. See to it you have actually qualified yourself for the job and also are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will assist you install a new tub in your washroom if you have actually already gotten a brand-new bathtub as well as don't need to change the arrangement of your previous water supply pipes.
Your tools as well as material checklist should comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before moving on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type should be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Using the two wood boards under its feet, position the bath tub in the required setting. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bathtub until the level checks out level.
To install faucets, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill up the tub and likewise check the overflow outlet and the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also securing around the bathtub must wait till the tub has actually been utilized a minimum of once as this will certainly settle it right into its final position.
Getting ready for the Installment
To start with, the supporting framework provided with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, resulting in difficulties with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to enable the activity experienced when the tub is in use. The sealer can break relatively early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about Installing A Bathtub? Try to leave feedback further down. We will be pleased to know your feelings about this blog. We are looking forward that you visit us again before long. Are you aware of somebody else who is curious about the subject? Feel free to share it. Thank you for your time. Don't hesitate to come by our site back soon.
Ready to assist.